Français	Home Advantages Microlubrication Spraying Principles Microlubrication Spraying Applications Products Quick choice ECOPULS ACOPULS ECOFLUX ACOFLUX Microlubrication control centres Spray control centres Microlubrication nozzles Spray nozzles Rack of nozzles News Contact
	ACOPULS systems	Rechercher Printable version Legal notices / Site map

AP1EG-V AP8EG-2E-V AP3EG-3E-V AP4EG-RAU-V AP4EG-4I-05V

• Way of functioning
• Duty cycle
• Applications
• Applications at high pace
• Models
• Standard configurations
• Standard options
• Samples

Way of functioning

ACOVAL microlubrication systems of the type PULS are instantaneous lubrication systems. They deliver an amount of liquid each time they are activated. They can be used:

• (1): to deliver an amount of liquid without using air to drive the liquid
• (2): most often with a nozzle which focuses or sprays the liquid with compressed air.

Duty cycle

In he case (1) where an amount of liquid is delivered without using compressed air to drive the liquid, it is important to take into account the superficial tension phenomenon.

The driving duration and the time interval between two drives must allow an accurate working of micropumps.

In the case (2) where a nozzle focuses or sprays liquid, the driving duration of the system must be:

• the same as the time required to spread the liquid (sample: a 3 seconds machining operation)
• enough to allow the air pressure to establish at the nozzle and to treat the amount of liquid delivered by micropumps.

The time interval between two drives must be enough to allow a correct system initialisation.

Applications

The systems ACOPULS are often used:

• to make short time spaced machining operations
• to lubricate forming operations when the load is manual
• to lubricate assembly operations.

Applications at high pace

Typical samples concern cutting, stamping and high pace machining operations.

The user often want a system of type PULS to work at the same rate as his equipment (his press or his machine tool). It is often a mistake because:

• The number of delivered liquid quantities is so large that the liquid flow may be too important even with low capacity micropumps.
• The compressed air pressure may not be able to take a good place in the nozzle. The functioning may be disturbed.

So it is better to use a system of the type ECOFLUX or ACOFLUX with a lower speed. The gas spreads the liquid out all along the time.

Models

These models in a cabinet generally include between one and six micropumps.

The liquid flow of each micropump is adjustable.

There is only one air flow setting or an air flow setting for each nozzle.

Standard configurations

These systems are fitted with:

• a 300 ml tank
• for each micropump:
  • a 1.5 meter transparent coaxial hose
  • a copper coaxial nozzle with its fastening

Standard options

• 0.5 ; 1 ; 2 ; 3 ; 5 ; 9 ; 10 litre tank
• Low level switch
• Automatic filling device
• Micropump selection by groups
• Attachment magnet under the system
• Attachment magnets for the nozzles
• Half capacity micropumps
• Double capacity micropumps
• VITON seals
• Stainless steel sheathed coaxial hoses
• Nozzles

Samples

AP1EG-V	a micropump a solenoid valve an one litre tank with a low level switch a stainless steel sheathed coaxial hoses a 150 mm copper coaxial nozzle.
AP8EG-2E-V	eight micropumps two solenoid valves a five litre tank with a low level switch eight stainless steel sheathed coaxial hoses eight short coaxial nozzles.
AP3EG-3E-V	three micropumps three solenoid valves a three litre tank with a low level switch three stainless steel sheathed coaxial hoses three nozzles each micropump are driven separately.
AP4EG-RAU-V	four micropumps a solenoid valve an one litre tank with a low level switch four stainless steel sheathed coaxial hoses four short coaxial nozzles.
AP4EG-4I-05V	four half capacity micropumps four selector switches manual switch automatic switch an one litre tank four stainless steel sheathed coaxial hoses four nozzles.